Исключительно мобильный и надёжный.Технические параметры Потребляемая мощность 720 Вт; Число оборотов холостого хода 21000 об/мин; Ограничитель глубины фрезерования 15 - 70 мм; Макс. глубина фрезерования 70 мм; O шлицевой фрезы DOMINO 8, 10, 12, 14 мм; Регулировка высоты фрезы 10 - 50 мм; Фрезерование в «ус» 0 - 90 °; O разъёма пылеудаления 27 мм; Масса 5.2 кгПреимуществаВысочайшая прочность соединений на шипах размером до 14 x 140 ммЗапатентованный и уникальный для ручных машин высокоточный принцип фрезерованияЗначительная экономия времени по сравнению со стационарным станкомБыстро и просто регулируемые упоры для точных результатовСистемная оснастка подходит для обоих пазово-дюбельных фрезеров DOMINOОсновные области примененияМебель из массива древесины, рамные и шиповые конструкцииВходные и межкомнатные двери, рамные конструкцииИзготовление подстольев и подстульевИзготовление прочных соединений в «ус»Выбранные в четверть и профилированные рамные фасады для мебелиСоединение широких брусков обвязки (например, столешницы)Рамные и стоечные не несущие деревянные конструкции (наружные и внутренние)Комплект поставкифреза DOMINO O 12, Упор дополнительный ZA-DF 500, пустая коробка для шипов 2 шт., гаечный ключ SW 12, в систейнере SYS 5 T-LOC..
Идеальное сочетание мощности и комфорта.Технические параметры Потребляемая мощность 1400 Вт; Число оборотов холостого хода 10000 - 22500 об/мин; O зажимной цанги 6 - 12.7 мм; Ход фрезы 70 мм; Точная регулировка глубины фрезерования 8 мм; Отверстие в опорной пластине 63 мм; O разъёма пылеудаления 27/36 мм; Масса 4.5 кгПреимуществаУстойчивость благодаря двустороннему зажиму стоекУдобная смена фрезы с помощью балансира и храповика, быстрее едва ли возможноПростая регулировка глубины фрезерования с точностью до 1/10 ммСистема быстрого торможения и ММС-электроникаСмена копировального кольца без инструментаУдаление до 99 % пыли при обработке кромок – благодаря вытяжному кожуху и пылеулавливателюОсновные области примененияЗакругление кромок, снятие фасок, выполнение выборок и профилированиеФрезерование фигурных и круглых вырезов с помощью универсального фрезерного шаблонаИзготовление пазов для задних стенок, врезание шпонокФрезерование пазов под уплотнитель или замки и петли с помощью спец. приспособленияФрезерование минеральных материалов (макс. 45 мм)Комплект поставкипылеулавливатель, зажимная цанга O 8 мм, зажимная цанга O 12 мм, боковой упор с системой точной регулировки, копировальное кольцо O 30 мм, верхний вытяжной кожух, гаечный ключ SW 24, в систейнере SYS 4 T-LOC..
Шлифовальная машинка LHS 2 225/CTL 36-Set PLANEX Festool 576696 ТЕХНИЧЕСКИЕ ДАННЫЕ:
Потребляемая мощность. Вт: 400Частота вращения при эксцентриковом движении, об/мин: 5 000 - 8 500Ход шлифования, мм: 4,00Диаметр сменной шлифтарелки, мм: 220Диаметр шлифматериала, мм: 225Длина, м: 1,2 / 1,65Диаметр разъёма пылеудаления, мм: 36/27Масса (длина 1,20 м), кг: 4,00Масса (длина 1,65 м), кг: 4,70Тип привода: Сеть КОМПЛЕКТ ПОСТАВКИ:Удлинитель ручки VL-LHS 2 225, клипса-фиксатор SC-LHS 2 225, фиксатор кабеля KV-215 (в упаковке 5 шт.), Granat P180, 5 шт. в упаковке, сетевой кабель с разъёмом plug it (4 м), шлифтарелка диаметр 220 мм включая демпфирующую подошву, пылеудаляющий аппарат CTL 36 E AC PLANEX (в картонной упаковке). УПАКОВКА:в систейнере SYS3 XXL 337СПЕЦИАЛИЗАЦИЯШлифование потолков и стен.Эксцентриковое движение шлифования: идеальный способ для получения поверхности стандарта качества Q3 и Q4.Обработка сухой шпатлёвки, гипсовой штукатурки, дисперсионной шпатлёвки. ПРЕИМУЩЕСТВАДа будет свет! Стены и потолок идеальны. Новый PLANEX со светодиодной подсветкой.Новое поколение шлифмашинок для стен и потолков PLANEX совершает революцию в сухой отделке благодаря светодиодной подсветке и эксцентриковому движению. Светодиодное кольцо выполняет функцию встроенной контрольной лампы и выявляет неровности прямо в процессе работы. Эксцентриковое шлифовальное движение обеспечивает превосходное качество поверхности - без дорогих доводочных операций. Свой вклад в значительное повышение производительности шлифования стен и потолка вносят возможность регулирования прижима нового PLANEX к обрабатываемой поверхности, изменяемая рабочая длина машинки и удобная T-образная рукоятка. Подробнее: https://inalliance.net/p1289893080-shlifovalnaya-mashinka-lhs.htmlТЕХНИЧЕСКИЕ ОСОБЕННОСТИ LHS 2 225 EQ-Plus FestoolОптимальная подсветка в процессе шлифования
Светодиодное кольцо выявляет неровности на поверхности прямо в процессе шлифования и освобождает от затратных доводочных операций. Эксцентриковое движение шлифованияДля достижения идеального качества поверхности без видимых рисок. Воздушный дроссель управления силой всасывания пылеудаляющего аппаратаПозволяет устанавливать оптимальный прижим нового PLANEX к обрабатываемой поверхности, практически полностью снимая нагрузку с рук и корпуса маляра во время работы на стенах и потолке. Регулируемая рабочая длинаВсего одним щелчком рабочая длина быстро подгоняется под условия работы. Будь то узкие помещения или высокие потолки. Клипса-фиксатор обеспечивает порядокT-образная рукоятка машинки PLANEX имеет идеальную длину 1,2 м практически для любой рабочей ситуации. Специальный зажим фиксирует всасывающий шланг и сетевой кабель на рукоятке на удобном расстоянии от руки. Работа без пылиКомбинация с пылеудаляющим аппаратом CT 36 E AC-PLANEX позволит Вам работать без пыли и вреда для здоровья. Шлифовальные машинки для стен и потолков PLANEX: PLANEX easy Festool, PLANEX LHS 2 225 Festool, лампа бокового света STL 450-Set Festool разных областей применения и разных требований к качеству поверхности мы снабдили наши шлифмашинки PLANEX разными функциями. Сравните прямо сейчас и сделайте правильный выбор для своих задач: Лампа бокового света STL 450-Set Festool 202911 Разработанная специалистами Festool уникальная оптика даёт сильно сфокусированный луч света, в котором сразу проявляются все неровности и дефекты зашпаклёванной поверхности.Вы можете контролировать результат обработки поверхности уже в процессе работы...
Festool TXS 2,6-Plus cordless drill/driver (art. no. 576101)SpecializationFurniture assembly Installation of skirting boards, sockets, lamps, curtains Installation of wheel arches and door linings Light drilling and screwdriving work in wood, metal and plasticYou don't have to be a giant to do great things.Lightweight but extremely powerful. The 10.8 V TXS cordless drill/drivers in the classic T-shape feature powerful torque that works effectively even in hard-to-reach places. With their exceptionally compact design and clever weight distribution, they are ideal for overhead work. And with long-lasting lithium-ion batteries with charge level indicator, CENTROTEC quick-change system and 12-speed torque setting with torque off, they are suitable for professional use. High-performance Li-Ion battery for maximum runtime FastFix attachment and CENTROTEC quick change chuck 12-stage adjustment and torque off for precise screwdriving Impressive ergonomics and low weight (0.9 kg) for easy drilling and screwdriving Compact and optimally balanced T-shape makes it easy to work even in hard-to-reach places Built-in LED light and battery level indicatorCharacteristicsBattery voltage: 10.8VSpeeds: 2Number of vol. cold stroke 1/2nd speed: 0 - 430/0 - 1300 rpmDrilling diameter, wood/steel: 12/8 mmTorque adjustment, 1/2 speed: 0.3 - 3.4 NmMax. torque dr/st: 10/16 NmChuck clamping range: 1 - 10 mmLi-ion battery capacity: 2.6 AhWeight with lithium-ion battery: 0.9 kg..
Shock cordless drill screwdriver Metabo SB 18 LT BL 2 x 5.2 Ah (art. UA602316840)The cordless impact drill boasts versatility and compactness for a variety of tasks.It is equipped with a high-performance percussion mechanism, which allows you to use it not only for drilling in wood, but also to drill bricks or masonry.TM Metabo's unique brushless technology has a high resource that ensures maximum productivity when drilling or wrapping screws in wood.The Metabo SB 18 LT BL cordless cordless drill / driver has a shortened body base and improved ergonomics compared to previous models.You can also note the presence of electronics that protect the tool from overload and overheating of the engine.By standard, a tool of this class, equipped with a reverse and a powerful two-stage gearbox.It has smooth torque adjustment, which allows you to adjust the screwdriver to your needsHigh-quality metal chuck securely clamps drills with a diameter of 1.5 - 13 mm.Built-in LED backlight, with residual light for a few seconds, after turning off the tool, to illuminate the workplaceWith practical strap hook and nozzle compartment, with fixation to choose from right or leftBattery packs with capacity indicator for charge level controlUltra-M technology: maximum power, gentle charging and 3-year warranty on both the tool and the battery packThe delivery set includes:Compartment for nozzlesHook for carrying on a belt 2 Li-Power accumulator blocks (18 V / 5,2 Ah)Charger ASC 145 "AIR COOLED"Metabo SB 18 LT BL cordless cordless drill / driverCase metaBOX 1Specifications:Metabo brandBattery poweredBattery voltage 18 VBattery capacity 5.2 AhNumber of batteries 2 pcsSB seriesMax. torque, Nm 75/34Twisting / drilling / impact drilling modeMax. drilling diameter (wood), mm 38Max. drilling diameter (metal), mm 13Max. drilling diameter (stone, concrete), mm 13Li-Ion battery typePush speed adjustmentNumber of operating speeds 2Number of revolutions 1st speed, 600Speed 2nd speed, rpm 2100Max. number of revolutions, rpm 2100The cartridge is non-removable / keylessFeatures of illumination / overload protection..
Соединяет шины-направляющие без малейшего зазора.Два соединителя обеспечивают надежную и идеально ровную стыковку двух шин-направляющих. Функция самовыравнивания облегчает эту процедуру. Соединители п..
Olfa GSR-2 scraper for glass and film removal; quick-change stainless steel blade L = 120 mm; hole for fastening the lace; resistant to solvents, acids, oils and fats; the spare blade container also serves as a blade cover; 6 blades in a set (art. 894510)Compact scraper for glass with stainless steel bladeThe scraper handle is as wide as the replaceable stainless steel blade. As a result, it allows you to clean bottlenecks, corners and curved surfaces. It can also be very useful at home, for example, for cleaning ceramic tiles, fireplace glass, etc.In addition to the blade, the stainless steel blade is also equipped with a plate and screw, making the scraper ideal for use with water and detergents. The hole at the end of the handle allows you to attach a string or safety rope, which is important when working at height.The handle and blade protection of this scraper are made of polypropylene resin reinforced with fiberglass, which provides increased strength and resistance to acetone.The plastic container for spare blades (also serves to protect the blade) has a safety function, which is very important when used as a blade protection. The container contains 6 GSB-2S blades. No tools are required to replace the blade. To replace the blade, loosen the screw (1 turn is enough), lower the metal plate down and remove the blade jammed between the plastic protrusions of the handle...
Olfa GSR-1 / 3B scraper for glass and film removal; quick-change stainless steel blade L = 120 mm; hole for fastening the lace; resistant to solvents, acids, oils and fats; 3 additional blades in a set and a cover for a blade (art. 890552)Glass scraper with stainless steel bladeThe handle and blade cover made of stainless steel 120 mm wide made of polypropylene resin reinforced with fiberglass, provide increased strength and resistance to acetone. Together with the stainless steel plate that secures the blade, they form a 7 mm thick handle / with a mounting screw - 14 mm /. The grooves on the yellow surface of the handle and the black protective blade cover help to find a safe and comfortable way to hold the tool. The scraper is very light, weighing only 115 grams.After removing the black blade cover, it can be transferred to the other side of the handle, increasing its thickness (14 mm) and ease of use. The lid can be moved to the left or right to perfectly suit the cleaning conditions. Special protrusions on the inside of the blade guard help keep the cover in place. Holes on the sides of the handle allow you to attach a string or safety rope to prevent the tool from falling, which is important when working at height.No tools are required to replace the blade. To replace the blade, loosen the screw (1 turn is enough), lower the metal plate down and remove the blade jammed between the plastic protrusions of the handle.The tool is intended for work related to the preparation of shop windows and window panes for gluing window films, protective films, burglary-proof, sun-protection and darkening films, removal of old film from glass and shop windows.In the package with the symbol GSR-1 / 3B, in addition to the tool with the blade, there are 3 additional blades with the symbol GSB -1 / S...
Scraper Olfa XSR-600 X-Design professional L = 600 mm; quick-release blade 100 mm; suitable blades BSF, BS, BS08, LB 18mm; for preparation of surfaces during repair and construction works; the blade can be mounted on the sharp or blunt side; reinforced handle (art. 885515)Powerful scraper with 60 cm long handle.The tool for the works connected with preparation of surfaces during repair and construction works. The strong structure allows to level and clear walls and floors of the remains of old facing, plaster, couplers, old paint and varnish coverings or glue. The scraper can be equipped with a wide flexible BSF blade, a narrow and rigid BS blade or a hardened professional blade BS08 0.8 mm thick for particularly complex work. The tool can also be equipped with a standard 18 mm LB segment blade.Depending on the needs, the blade can be installed in the scraper with a sharp or blunt side. Due to the possibility of hammering, the blade handle is reinforced and for safety it has a hole for attaching the sling or fishing line.The handle is made in yellow-black X-Design style, which is a combination of softer black elastomer and harder yellow composite filled with fiberglass, which provides exceptional strength and resistance to solvents, acids, oils and fats. The scrapers are equipped with a comfortable and safe protective cover made of branded yellow plastic...
Shkrebach-nizh OLFA BTC-1 for cutting shkiri, plastic, gum, beveling edges and cleaning smooth surfaces; swidkozminne leso 43 mm; mitsny capture and zhorstke lezo (art. 860510)Knife, cutter and scraper in one moldThe Bettachi knife has been on the Japanese market since 1982 and has proven to be an excellent tool for cutting leather. This knife is based on a tool used in medieval Japan to cut leather and straps for saddles and samurai armor. The robust design of this tool allows it to be used in a variety of ways and allows for high force applications. The screw fixation ensures that the blade is securely fixed.This knife has gained recognition in the upholstery, saddlery and plastics industries as a tool for cutting, shearing and chamfering edges. It also works very well as a scraper for cleaning smooth surfaces. The strong handle and rigid blade make it possible to cut even difficult materials such as reinforced rubber bands.The 43mm wide BTB-1 replacement square blade has two very sharp cutting edges protected by a steel sheath. Blade replacement does not require additional tools...
Olfa DC-4 container for used blades and broken segments; has a push-open cover for safe clamping of the blade; possibility to suspend or fasten to a belt (art. 983513)Container for used blades and broken segmentsThe container allows you to safely store used blades and broken segments until they are transferred for controlled destruction or recycling. The container is equipped with a safe break to facilitate the separation of used parts of segmental blades and holes, which allows it to be hung at the workplace or attached to the belt...
Купую Festool тільки в цьому магазині. офіційний імпортер, гарантія якості, своя ремонтна майстерня.. а головне в наявності завжди є усі комплектуючі. ..
Андрій Пришляк
2022-04-14 10:59:57
Купував пилу Makita HS7611, ціна супер, найнижча серед усіх що я бачив. гарантія є. Швидко відправили Новою Поштою. Дуже дякую!..